2021 Fractional co2 laser pigment removal/laser skin resurfacing anti aging wrinkle removal equipment5.jpg

 

 

Principle:

The laser is emitted in a scanning lattice method to form a burning area composed of laser action lattices and intervals on the epidermis. Each laser action point is composed of a single or several high-energy laser pulses, which can penetrate directly to the dermis layer in an instant It vaporizes the tissues in wrinkles or scars and stimulates the proliferation of collagen, which in turn initiates a series of skin reactions such as tissue repair and collagen rearrangement. Under the action of the laser, collagen fibers shrink by about one-third, small wrinkles are flattened, deep wrinkles become shallower and thinner, and the skin becomes firm and shiny.

Laser through the CO2 laser’s microvascular reconstruction effect, the oxygen content of gynaecology tissue will increase, mitochondria will release more ATP, cell function will be more active, and then the secretion of gynaecology mucosa will be enhanced, the color will be lighter, and the lubrication will be enhanced. At the same time, through restoration The gynaecology mucosa normalizes the PH value and flora, reduces the recurrence rate of infections, and restores female reproductive tissues to a younger level. In addition, the private laser completely subverts the traditional birth canal repair method: painless and non-invasive to solve the problems of postpartum genital tract leakage, relaxation, decreased sensitivity and lubricity, and repeated inflammation.

2.jpg

Fractional Skin Resurfacing and Skin Tightening
(Arfurla laser)
Before and After The Arfurla laser is a resurfacing laser that can dramatically improve one’s skin without significant downtime or discomfort. This laser is ideally suited for the treatment of sun damage, fine lines, resistant pigmentation, acne scars, roughened textures, and enlarged pores. It may also help reduce fine lines and skin laxity on the face, neck, chest and arms and hands with to no downtime.
 
What does fractional resurfacing mean exactly?
Fractional resurfacing lasers are very exciting because they offer significant skin improvements with relatively to no downtime. Compared to traditional resurfacing lasers that target the entire skin surface, fractional devices only target small areas of the skin (like individual pixels in a camera) with each laser pass. The idea behind this technology is that if only a fraction of the entire skin surface is hit with the laser then the healing time will be much faster and the downtime greatly reduced. The normal skin surrounding these laser hot spots will in essence allow for more effective tissue healing and production of collagen.
 
A significant advantage of the Arfurla laser is that no topical anesthetic creams or messy gels are necessary for treatment. Treatment is described only as a mild heat sensation with no real pain by most patients.
How does Arfurla work?
It’s resurfacing laser that creates small microscopic wounds within the skin that heal and stimulate new collagen production that in turn tightens and smoothes out the skin’s surface.

4.jpg

How many treatments are required?
Most patients see a significant improvement in the appearance of their skin after the first treatment. Depending upon the condition of your skin and the body location being treated, the average patient requires two to five treatment sessions for best results.
How much improvement is there?
Most patients see improvements in skin texture, tone, and pigmentation within a week of treatment. More significant improvements in fine lines and skin laxity are noted after several sessions. The formation of new collagen continues after the last treatment session so continued improvements are usually seen up to four to six months after the last treatment.
Is it painful?
The Arfurla laser treatment is very well tolerated and has almost no discomfort – a significant advantage over some other fractional resurfacing devices. A mild burning sensation may occur towards the end of treatment but this is usually very mild in nature and lasts only a short while (30 minutes to three hours).
Where can the Arfurla be used?
The Arfurla is safe to use on virtually any area of the body. It is most commonly used to treat sun damage and aging changes on the face, neck, chest, arms, and hands. It may at times be used in conjunction with other lasers depending upon the condition of your skin. Your skin looks brighter, fresher and more relaxed within a few weeks of the procedure.

dd.JPG

 

Safe treatment:

Totally safe, and tested by hundreds of women in the world; the ideal wavelength is absorbed by the mucous membrane micron, to avoid any thermal damage by deep tissue or organ

Fast treatment:

Each treatment less than 30 minutes and 1-3 times treatment can completely solve the gynaecology problems

Effective treatment:

Effective for all women who have the loosen gynaecology; and effective prevention of gynecological inflammation

Painless treatment:

The patients only can feel warm/hot inside, cannot feel any pain

3.jpg

Fractional co2 laser.jpg

Screen.JPG

11.jpg

Effective:

Fast tightening, lasting constriction, tightness to improve 60%;

Improving secretion, moisture level to improve 80%;

Vulva rejuvenation, lighten pigment and pinks labia parts, delicate degree to improve 70%

 

wrinkle removal (2).png

Parameters:

Wavelength: 10600nm
Laser apparatus: Sealed off laser device simulated by direct current
Optical beam quality: TEM00
Output power: 30w
Spot size: 0.02~0.05mm2
Aiming beam: Red semiconductor laser (650nm)
Beam transport device: Articulated arm with 6-joint and balance weight
Working mode: Continuous operation
Output Mode: Continuous, single pulse, interval pulse and super pulse
Scan scope: Max 20mmx20mm Min 0.1×0.1
Scan graphics: Circle, triangle, square, rectangle,hexagon, ellipse, line
 Scanning Mode: Random , Normal and Midsplit scan
Energy:  1- 30W/60W
Distance:  0.1-2.6mm
Cooling system: circulating water cooling
Weight: 40kg
Dimension: 93*52*36cm
Power: 220V/110V


skin tightening.png

Co 2 laser machine Application:
Technology specification of co2 medical laser machine: Applications of co2 medical laser machine:
1.Remove acne, acne scar, scar and so on;
2.Dispel wrinkle around the eyes, crow’ s-feet, and wrinkle formed by lack of wate;
3.Effectively reduce the wrinkle on the face, forehead, the joints and striae gravidarum;
4.Dispel freckle, nevus zygomaticus and other spots formed by hyperchromic pathological changes;
5.Tighten skin and lift face;
6.Remove striae gravidarum and other deep scars.
7.Vaingal tighten and rejuvenation .
scar removal.jpg
bEFORE AND AFTER CO2.jpg
Before and After.jpg
Treatment of co2.jpg
Certifications:
wrinkle removal
Company Culture:
customers